Home
Home
Home
About Us
About Us
About Us
Products
Products
Products
Guest Book
Guest Book
Guest Book
Contact
Contact
Contact
Impressum
Impressum
Impressum
About Us
Heat Exchanger
Helium Leaktest on Heat Exchangers.
Page 1
Introduction to the Gas Laws
Introduction to the Gas Laws
Page 1
Introduction to the Gas Laws
Introduction to the Gas Laws
Page 2
Introduction to the Gas Laws
Introduction to the Gas Laws
Page 2
Introduction to the Gas Laws
Introduction to the Gas Laws
Page 3
The Flow of Gases in Leaks
The Flow of Gases in Leaks
Page 3
The Flow of Gases in Leaks
The Flow of Gases in Leaks
Page 4
The Flow of Gases in Leaks
The Flow of Gases in Leaks
Page 4
The Flow of Gases in Leaks
The Flow of Gases in Leaks
Page 5
The Flow of Gases in Leaks
The Flow of Gases in Leaks
Page 5
The Flow of Gases in Leaks
The Flow of Gases in Leaks
Page 6
Connections to other Leak Test Adresses
Connections to other Leak Test Adresses
Page 6
Connections to other Leak Test Adresses
Connections to other Leak Test Adresses
Page 7
Helium Leak Test on Heat Exchangers
Helium Leak Test on Heat Exchangers
Page 7
Helium Leak Test on Heat Exchangers
Helium Leak Test on Heat Exchangers
Page 9
Leak Detection with Tracer Gas Methods
Leak Detection with Tracer Gas Methods
Page 9
Leak Detection with Tracer Gas Methods
Leak Detection with Tracer Gas Methods
Page 10
Leak Test with Laser Beam
Leak Test with Laser Beam
Page 10
Leak Test with Laser Beam
Leak Test with Laser Beam
Page 11
The Download Page
The Download Page
Page 11
The Download Page
The Download Page
Page 12
Literature
Literature
Page 12
Literature
Literature
Page 8
Leak Detection and
Measuring Methods
Leak Detection and
Measuring Methods
Page 8
Leak Detection and
Measuring Methods
Leak Detection and
Measuring Methods
Short Introduction:
The test for leak tightness with helium and helium leak detectors becomes more and more important. The practice of leak detection on heat exchangers is described in this article. Three possible methods are discussed.
The test for leak tightness with helium and helium leak detectors becomes more and more important. The practice of leak detection on heat exchangers is described in this article. Three possible methods are discussed.
1.) The integral leaktest with vacuum in the volume around the tubes and helium at atmospheric pressure in the volume of the tubes.
The preparations prior to the test, the correct procedure during the test, the pumpdown and the response time are discussed, also problems and suitable gaskets and seals. Problem solving for negative test are described.
2.) The integral leaktest with helium pressure in the volume around the tubes and vacuum in the tubes.
This test is sometimes necessary, when the volume around the tubes has had a helium filling in the past, for example for a leaktest with the sniffer probe. The changes in test conditions are decribed. Also the calculations of the leakrate according to pressure changes are discussed and the possibility of cost reduction by reducing the helium concentration as a result of pressure increase is pointed out.
3.) The integral leaktest with helium pressure in the volume around the tubes and atmospheric pressure in the tubes.
This test requires long waiting times and is used only, when other methods are not possible and when the safety conditions allow a higher testgas pressure in the volume around the tubes. The test is carried out by measuring the helium concentration in the volume of the tubes. The value of the leakrate must be calculated. The procedure of this test, the calculation of the waiting time as well as the leakrate are described.
This article can be downloaded (~43 kB) as a winzip file. To do so, go to the download page and fill in the form and submit.After that you will be led to the download automatically. To the download page click here. After "unzipping" the file is a MS-Word-file.
Download as PDF-file
Download as PDF-file
Print as MS-word-file
Print as MS-word-file
